The Yaskawa / Magnetek GPD /G5 Sine-Coded Pulse Width Modulated AC Motor Drive generates an adjustable voltage/frequency three phase output for. TTThhhooommmpppsssooonnn CCCooo RRReeellleeeaaassseeeddd /// /// 2. Magnetek GPD AC Drive Start Up and Adjustment Guide. Magnetek G5 GPD | Drives | NEW IN STOCK | CALL or Click for Quote.
|Published (Last):||18 December 2008|
|PDF File Size:||18.24 Mb|
|ePub File Size:||3.3 Mb|
|Price:||Free* [*Free Regsitration Required]|
Sometimes it will take a minor adjustment to a parameter or set of parameters. Please enter 5 or 9 numbers for the ZIP Code. Monitor Selection Factory setting: The first digit of the value to be set blinks. Make additional wiring connections required for the external control functions selected by the parameter programming. No fault relay 1: User Parameter Bpd Value Factory setting: At that point you can call on the repair experts at Precision Electronic Services, Inc.
EMS Yaskawa G5 Magnetek GPD | eBay
Set b 1 – 0 1 to data ” 0 ” See Multi-step Speed Setting, paragraph 5. A general procedure for tuning these parameters is as follows: This jumper will override both the Auto and Digital Operator frequency references, regardless of the programming of parameter b 1 – 0 1.
Available dynamic braking components are listed in Table A through A S-Curve Characteristic Time at Decel End Setting of these parameters determine the S-curve starting and ending characteristics of the acceleration and deceleration ramp.
Fault code ” o P E 1 1 ” is displayed if either of the following conditions is detected: The addition of Integral Time will cause the steady-state error to approach zero. The unit should arrive in a few days so our laser should be back in production for a few more years to come Thanks for your help Ad van D – MB, Canada. A Control Method Selection Number of Auto-Restart Attempts Factory setting: M Drive output has open phase Problem in drive-to-motor wiring.
Power is removed from the Drive. The higher the setting, the slower the PID output will change. A setting of ” ” will disable stall prevention during acceleration.
Yaskawa / MagneTek / Saftronics / Omron Magnetek G5 GPD 515 Drives
M Short circuit on drive output terminals Very low impedance on output of drive. Table lists the possible data setting values for these parameters, with the function and a brief description for each one.
M Braking transistor failure Braking transistor failure.
The drive will continue to operate, and a “Minor Fault” contact will be closed if a multi-function output is programmed for the condition. Setting this parameter to “” resets magetek settings to the user-defined defaults, rather than to factory defaults. The time should be adjusted so that this minimal error is attained as fast as possible, without making the system oscillate. Digital “Motor Operated Pot” Factory setting: The following table shows which Gdp Group s appear under which Mode.
By monitoring DC bus voltage, the deceleration rate is automatically adjusted so that deceleration can be completed in the shortest amount of time, regardless of the set deceleration time. Good morning, We are very happy with your service, delivery, and purchase. Mouse over to Zoom – Click to enlarge. This ensures your drive will function as required when received back at your facility. Quality repairs by factory trained technicians that are done fast at a price that will save you money.
mxgnetek Reapply power to the drive. When operating several motors with one drive, install a thermal overload 51 on each motor. Take apart the military style connector at the motor. Our company became an authorized service provider for Magnetek GPD repair in and has performed hundreds of repairs on the various models and sizes of the drive since then. When all of the parameters are entered, execute AutoTuning.
To make this website work, we log user data and share it with processors. Attach the Remote Mount Resistor Unit maintaining a minimum 1.
It is recommended that this parameter be enabled at all times. I found your company on line ,the sinumeric PCU50 was an obsolete part from the machine manufacturer so we where dead in the waterafter speaking to Joe he was very helpful and knowledgeable, he knew what we needed and the magnete was in stock new 55, but he also gave me some more economic options to choose fromi opted for the new unit and they shipped it the same day.
Sign in to check out Check out as guest.
Assistance, if required, is available from your sales representative. The output is magneyek held at that frequency for the duration of the dwell time at stop b 6 – 0 4.