LF JFET Input Operational Amplifiers. These are the first monolithic JFET input operational amplifiers to incorporate well matched, high voltage JFETs on the. LF datasheet, LF circuit, LF data sheet: STMICROELECTRONICS – WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIERS,alldatasheet. LF datasheet, LF circuit, LF data sheet: TI – LF/LF/LF/ LF/LF/LF/LF JFET Input Operational Amplifiers,alldatasheet.

Author: Kazrakasa Bazragore
Country: Dominican Republic
Language: English (Spanish)
Genre: Travel
Published (Last): 20 December 2007
Pages: 216
PDF File Size: 16.35 Mb
ePub File Size: 8.10 Mb
ISBN: 928-2-22018-509-4
Downloads: 64100
Price: Free* [*Free Regsitration Required]
Uploader: Zulkit

The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. However, if the feedback pole is less than approximately six times the expected 3-dB frequency a lead capacitor should be dataeheet from the output to the input of the op amp.

When the LFx5x is manufactured, the device is always handled with conductive finger cots.

Precautions should be taken to ensure that the power supply for the integrated fl357 never becomes reversed in polarity or that the unit is not inadvertently installed backwards in a socket as an unlimited current surge through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a destroyed unit.

Page numbers for previous revisions may differ from page numbers in the current version.

Very popular in portable systems with low. To have a significant effect, guard rings must be placed on both the top and bottom of the PCB.

TI is not responsible or liable for any such statements. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed.


LF Datasheet PDF ( Pinout ) – Series Monolithic JFET Input Operational Amplifiers

Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. Output Impedance Figure Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Voltage Swing Figure 5. Open-Loop Voltage Gain Figure Settling Time Test Circuit 8.

Pin Configuration and Functions To minimize the effect of any surface leakage, lay out datasehet ring of foil completely surrounding the inputs of the LFx5x and the terminals of capacitors, diodes, conductors, resistors, relay terminals, and so forth, connected to the inputs of the op dayasheet, as in Figure This data is subject to change without notice and revision of this document.

Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage.

what kind of reference type does “datasheet’ belong to?

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are catasheet.

This information is the most current data available for the designated devices. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. These devices can replace expensive hybrid and datasheett FET operational amplifiers.


TI is not responsible or liable for such altered documentation. Input Bias Current Figure 2. Important Information dataasheet Disclaimer: Nonetheless, such components are subject to these terms.

LF357 Datasheet PDF – National Semiconductor

Common-Mode Rejection Ratio Figure TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. A feedback pole is created when the feedback around lv357 amplifier is resistive. In no event shall TI’s liability arising out of such information exceed the total purchase price of the TI part s at issue in this document sold by TI to Lf35 on an annual basis. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications.

This component has a RoHS exemption for either 1 lead-based flip-chip solder bumps used between the die and package, or 2 lead-based die adhesive used between the die and leadframe. This glossary lists and explains terms, acronyms, and definitions.

It is the time required for the error voltage the voltage at the inverting input pin on the amplifier to settle to within 0. These amplifiers feature low input bias and offset currents, as well as low offset voltage and offset voltage drift, coupled with offset adjust which does not degrade drift or common-mode rejection.

Customers should validate and test their design implementation to confirm system functionality.