dell latitude c user s manual free pdf download november 12th linkthe dell? latitude c ez93 dell latitude c user guide owners. User guide • Read online or download PDF • Dell Latitude C User Manual • Dell Notebooks.
|Genre:||Health and Food|
|Published (Last):||6 February 2018|
|PDF File Size:||14.60 Mb|
|ePub File Size:||6.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 59 Speaker Assemblies: By pressing ‘print’ button you will print only current page. Removing The Keyboard Keyboard: Table of Contents Add to my manuals Add. Remove the speaker assemblies from the latutude case.
The latch will not function properly if the slider is oriented incorrectly. Page 41 Palm Rest: Page 68 Battery and Module Bay Latches: Turn the computer over and remove the M2. You must remove the display assembly before you remove the palm rest. Insert a screwdriver into the recess mnaual the EMI shield under the front left corner of the thermal cooling assembly, and pry the assembly up and out of the system board.
Insert a screwdriver into the recess in the EMI shield under the front left corner of the thermal cooling assembly, and pry cc540 assembly up and out of the system board. The placemat provides the number of screws and their sizes.
Connect the modem cable to the modem. Turn the computer over and remove the M2.
DELL LATITUDE C SERVICE MANUAL Pdf Download.
Install a second memory module in the connector labeled “JDIM2. Remove the two M2 x 3-mm screws that are located in the hard-drive bay door labeled “circle P. To avoid possible damage to the system board, edll 10 to 20 seconds and then disconnect any attached devices.
This manual also for: Disconnect the fan power cable from the system-board interface connector and remove the hybrid cooling fan.
Page of 79 Go. Lift the keyboard straight up about an inch and then rotate it forward toward the front of the computer, until the key face is resting on latitudee palm rest.
Place the right side of the microprocessor thermal cooling assembly under the palm rest and lower the assembly onto the system board. Turn the computer over and open the display.
Removing The Display Bezel Carefully separate the bezel from the top cover to avoid damage to the bezel. Page 2 Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.
Disconnect all other external cables from the computer. This manual also for: Pull straight up on the attached pull-tab to lift the modem out of its connector on the system board and disconnect the modem cable.
Dell Latitude C640 User Manual
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Connect the reserve battery cable to the reserve battery connector on the system board and then route the battery cable through latifude opening in the EMI shield to the battery tray.
Hard Drive Hard Drive: Microprocessor Thermal Cooling Assembly: By pressing ‘print’ button you will print only current page.
Carefully turn the keyboard over. To print the manual completely, please, download it. Page 45 Microprocessor Thermal Cooling Assembly: Slide the hard drive out of the computer. If you have a Hitachi display panel, remove the two M2 x 4-mm screws from the center of the left side of the manula panel.
System Board System Board: Thank you for purchasing this Factory Service. Display Latch Before You Begin: Rotate the hinges forward at an angle of approximately 90 degrees to the front mxnual the display assembly.
Battery and Module Bay Latches: Read “Preparing to Work Inside the Computer” Trademarks used in this text: The mamual on the keyboard are fragile, easily dislodged, and time- consuming to replace. Remove the hard drive. Microprocessor Module Microprocessor Module: Place the keyboard on the palm rest at the front of the computer with the keys face down and the connector toward the back of the computer.
,anual The Keyboard Keyboard: Don’t have an account? Align the keyboard boss supports, fit the left side of the keyboard into place, and then snap the right side of the keyboard into place. The memory module must be inserted at a degree angle to avoid damaging the connector.